RK3588 4x Cortex-A76 2.4GHz Custom, WF-C3588-K4, AndroidSBC, Liverpool

TL;DR: RK3588 4x Cortex-A76 2.4GHz Custom

SHENZHEN, China, September 12, 2026 - The WF-C3588-K4 board line at Wanlin Longgang closed lot 158 this week. 11,670 units are now booked for Liverpool, United Kingdom, shipped FOB with the full certification file attached.

AndroidSBC release of the nine-variant custom RK3588 motherboard platform for OEM and ODM projects serving Liverpool, United Kingdom. One Rockchip RK3588 silicon, nine custom motherboard variants. The WF-C3588 programme covers custom Android boards, industrial control, core board and SOM work, signage, kiosk and POS, robotics, NVR, edge AI and ARM PC lines, all on the same octa-core 8nm platform with 6 TOPS NPU. Every board leaves the Wanlin Longgang plant with a per-lot certification pack and a burn-in record traceable by unit barcode. Buyers in Liverpool and United Kingdom can mix custom variants inside a single framework agreement.

About AndroidSBC and the Rockchip RK3588 Board Family

AndroidSBC is the export brand of Wanlin Manufacturing Group. The group runs SMT, test and packing under one roof at Longgang in Shenzhen, and it has built custom boards on Rockchip silicon for overseas OEM customers for over ten years. The WF-C3588 line-up covers nine custom categories on the same Rockchip RK3588 octa-core 8nm silicon with 6 TOPS NPU: custom Android motherboards, custom industrial boards, core board and SOM carrier design, custom signage and video wall boards, custom kiosk and POS boards, custom robotics controllers, custom NVR boards, custom edge AI boards, and custom ARM PC and NAS boards. Buyers in Liverpool and United Kingdom can source any of the nine custom variants from one factory with one set of export documents.

WF-C3588-K4 Technical Specifications

All parameters in the table above are measured at 25C ambient. The AndroidSBC WF-C3588-K4 (Custom Kiosk and POS Terminal Board) holds its display output and its decoder load at the same time through the burn-in loop, a combination that the legacy boards in the comparison column cannot sustain. For United Kingdom importers sourcing the WF-Series, the 8GB + 64GB (WF-C3588-K4-B) variant is the typical configuration for the custom self-service and POS programmes use case, with a sustained weekly capacity of 5,000 pcs/wk on the Longgang line.

Challenges in Sourcing Custom Kiosk and POS Terminal Board for United Kingdom Buyers

Buyers in Liverpool who have sourced a custom kiosk and pos terminal board for a few seasons tend to separate two questions: can the factory hold the price, and can it hold the allocation. The second one is harder. The Rockchip RK3588 is allocated at wafer level, and a 11,670-unit order placed against trader stock is the order most likely to slip a quarter without anyone warning the buyer. The second issue is firmware, not hardware. Vendors promise the full certified software stack and then ship a bare AOSP image, and the failure only surfaces at the warehouse when the unit is powered on against the customer's app.

The third item is the certification file. A marking without a dated test report is a placeholder, and placeholder paperwork is what turns a routine United Kingdom clearance into a three-week hold. The answer AndroidSBC applies is to close the gap at the source. Custom variant assembled on the Longgang line, certified image burned, burn-in record traceable per unit, certification file issued with the lot. The nine WF-C3588 variants span self-service kiosks, ordering terminals, checkout systems, vending machines, parcel lockers, smart lockers, unattended retail, and POS registers and each carries three memory configurations, which keeps most United Kingdom requirements on a standard custom SKU rather than a from-scratch run.

On the United Kingdom side, the destination file matters as much as the board specification. In the United Kingdom UKCA marking now sits alongside CE, and Ofcom registration applies to radio equipment. The export desk prepares the destination-market file covering UKCA marking with Ofcom radio interface registration, administered by Ofcom, and releases it with the standard multi-market pack (CE, FCC, UKCA, RoHS, REACH). The lot is booked into Port of Felixstowe on the Felixstowe to Yantian lane.

Competitive Comparison: WF-C3588-K4 vs Competing RK3588 Boards

Competing boards in the custom kiosk and pos terminal board category sort into three camps: cheap catalogue boards with no customization, re-badge imports with a sticker but no engineering file, and source-factory custom boards with the BSP, the certification and the test bench in one building. The WF-C3588-K4 is in the last camp, and its edge is Rockchip RK3588 plus a factory that will route the I/O the project actually needs.

• vs standard SBCs in kiosks: the WF-C3588-K4 arrives with the serial bank, the payment profile and the kiosk ROM already in place, so the integrator does not build a stack from parts.
• vs POS chipset vendors: the 6 TOPS NPU adds vision features on the same board that runs the till, without a second compute module.
• vs turnkey terminal importers: the board-level customization path lets a kiosk brand change the I/O and the firmware without changing the terminal factory.
• vs unbranded boards: per-unit barcodes and burn-in records give the estate a real RMA trail instead of a swap-and-hope process.

Global Custom Kiosk and POS Board Market Trends

The Custom Kiosk and POS Board curve is what United Kingdom importers read before committing to a custom kiosk and pos terminal board programme. The number they quote is the Edge AI hardware segment at USD 26.9 billion in 2025 with a 32.7 percent CAGR to USD 108.2 billion by 2030 (MarketsandMarkets, Edge AI Hardware Market Report, 2025-2030), which serves as the closest public proxy for the silicon demand behind custom RK3588 boards. For Liverpool that resolves into three demand patterns across the WF-C3588 order book:

• Self-service ordering kiosk: a QSR estate runs ordering terminals with a locked launcher and nightly OTA updates.
• Display and signage refresh cycles: a longer content loop and a higher panel resolution now define the refresh trigger. The WF-C3588-K4 board carries that headroom without a board change.
• Smart vending machine: an operator adds shelf-camera stock checks with the NPU and cuts route visits by a third.

Channel research on the Custom Kiosk and POS Board segment keeps landing on the same point: the constraint is allocation, and allocation is held by factories rather than traders.

Across those three segments, Liverpool procurement has been shifting from spot quotes to framework agreements with a one-lot-per-month cadence, particularly where a custom Android, industrial, signage or robotics programme needs a twelve-month shipping window.

Partner Success Story: Cedarline Media Networks in Liverpool, United Kingdom

Cedarline Media Networks, a DOOH network operator serving the United Kingdom market, deployed 8,400 custom WF-C3588-S3 video wall boards for a control room and street network. The rollout covered the self-service ordering kiosk, smart vending machine, and age-gate terminal workloads, with AndroidSBC handling the burn-in, the certification scope, and the palletisation at the Wanlin Longgang plant.

• Deployed: 8,400 custom WF-C3588-S3 video wall boards for a control room and street network
• Region: Liverpool, United Kingdom
• Models used: WF-C3588-K4 (lead SKU), plus eight sibling custom RK3588 board variants in the same platform family
• Certifications handled: CE, FCC, UKCA, RoHS, REACH, IEC 62368-1, EN 55032, EN 55035, plus optional UL 60950-1, GMS, Widevine L1 and Dolby Audio per variant
• Logistics: FOB Shekou with the Wanlin Group Longgang source factory named on the export declaration, entering Port of Felixstowe via the Felixstowe to Yantian lane

"Twelve tiles, three boards, one head-end. The 8K decode carried the new line-map asset on first boot, and the OTA channel pushes firmware to street cabinets without a truck roll. AndroidSBC burned our CMS into the image before the lot shipped."

- Yasmine El-Sayed, IT Director

Field Report: an engineering review at the Wanlin Longgang plant, where the Liverpool buyer team walked the WF-C3588-K4 carrier design through schematic and stack-up sign-off

Reporter Jiang Bo, on the ground in Liverpool, United Kingdom. The buyer's hardware lead spent three days at Longgang reviewing the schematic, the stack-up, and the signal integrity report with the Wanlin engineering desk. Two net-class changes came out of the review and were folded into the next carrier revision before the tooling release.

The engineering desk ran a firmware re-flash drill on three units to confirm the recovery path a field technician would use.

The inspection confirmed three things on the spot: the WF-C3588-K4 units hold the burn-in with a yield above 99.18 percent, the loaded firmware image survives a 72-hour continuous loop without credential drift, and the pallets carry the matching certification file for the destination market, covering UKCA marking with Ofcom radio interface registration administered by Ofcom, cleared for entry at Port of Felixstowe on the Felixstowe to Yantian lane. Wanlin remains one of the few source factories currently shipping a nine-variant custom RK3588 motherboard line with a per-lot paper trail that United Kingdom importers can hand straight to their customs broker.

Filed by Jiang Bo, AndroidSBC field reporter, Wanlin Manufacturing Group export base.

WF-C3588-K4 Application Scenarios

The WF-C3588 line fits nine custom motherboard lanes, with the WF-C3588-K4 (Custom Kiosk and POS Terminal Board) as the lead SKU for Liverpool and United Kingdom programmes:

• Self-service ordering kiosk: a QSR estate runs ordering terminals with a locked launcher and nightly OTA updates.
• Checkout and POS register: a retail chain drives the register, the scanner bank and the payment terminal from one board.
• Smart vending machine: an operator adds shelf-camera stock checks with the NPU and cuts route visits by a third.
• Parcel locker bank: a locker network runs door control and a camera per bay on the multi-serial I/O profile.
• Ticketing kiosk: a transit operator prints tickets and reads QR passes on an offline-capable terminal.
• Age-gate terminal: a licensed venue runs on-device face age estimation with no cloud round trip.
• Unattended retail store: a smart store runs entry gates, shelf cameras and checkout analytics on one board class.
• Queue analytics display: a bank branch counts queues locally and posts wait times to the lobby screen.

Partnership Models for Liverpool Buyers

AndroidSBC opens the WF-C3588 to United Kingdom partners through three structures, and a single agreement can draw on more than one:

• OEM (your brand on our hardware): custom logo silk-print, custom packaging, custom boot animation, custom SKU label, and a private-label certification file.
• ODM (your spec on our reference design): schematic and stack-up review, carrier or motherboard redesign, custom firmware features, and a BSP port handled by the Longgang engineering desk.
• Distribution (your channel, our stock): regional distributor rights, channel rebate, stock holding at the factory, and a framework agreement with a monthly lot release.

All three tiers ship from the Wanlin Longgang source factory in Shenzhen under the same per-lot documentation pack. For Liverpool buyers, a typical first order on the WF-C3588-K4 is the 8GB + 64GB (WF-C3588-K4-B) configuration at MOQ 5,000 units per shipment, with standard-variant samples in 1-3 days and 15-30 days to mass production on custom runs.

Frequently Asked Questions

What exactly can be customised on an RK3588 motherboard from AndroidSBC?

Answer: The customization scope runs across five layers: hardware (PCB, PCBA, I/O, memory, storage), thermal (fanless passive, vented, wide-temperature, conformal coating), software (custom ROM, custom Linux, pre-installed apps, OTA), branding (logo, packaging, boot animation, SKU labels), and compliance (the certification file assembled for the exact configuration you ship). Most United Kingdom partners change two or three layers on a standard variant rather than commissioning a full custom run.

Can AndroidSBC port a custom Android ROM or a custom Linux BSP to our carrier board?

Answer: Yes. Under NDA, AndroidSBC delivers custom Android ROM work with proprietary services and a locked launcher, custom Linux images on Ubuntu, Debian, Yocto or Buildroot, BSP ports for customer carriers, and driver development for project-specific I/O. Source access is released to the partner, and the port is performed at Longgang, which matters because a vendor BSP rarely matches a custom carrier revision on the first try.

Can the 6 TOPS NPU on a custom board run our own AI models?

Answer: The NPU is fully open on the custom line. Bring the model in PyTorch, ONNX, TensorFlow or Caffe and the Longgang desk handles the RKNN quantization, the runtime integration and the validation against your board's thermal and memory profile. Custom AI algorithm integration is a standard line item on the ODM scope, and the resulting model ships embedded in the firmware image burned per lot.

What are the MOQ and lead times for a custom RK3588 motherboard?

Answer: Standard-variant samples ship in 1-3 days from stock, so your engineering team can start integration while the custom scope is being quoted. A custom run follows a 15-30 day mass-production window after schematic and stack-up sign-off. MOQ is 5,000 units per shipment on standard variants; on custom configurations the MOQ is negotiable against volume commitments, and small batch orders are accepted for pilot phases. A twelve-month framework agreement with monthly lot releases brings the per-lot MOQ down further.

What certifications does a custom board need for United Kingdom, and who handles them?

Answer: Yes, and the file travels with the goods. The pack covers CE, FCC Part 15, UKCA, RoHS 2.0, REACH and IEC 62368-1 with the EMC and safety reports for your configuration, dated within the prior year. AndroidSBC confirms any United Kingdom-specific addition at quotation stage, which is the point where the answer is still useful rather than expensive.

How long will AndroidSBC keep supplying a custom board?

Answer: The commitment is seven years minimum on supply, with security patches back-ported across the Android and Linux firmware tracks and OTA infrastructure for pushing firmware and RKNN model updates to deployed units. Long-lifecycle programmes in industrial, signage and robotics usually ask for the term in writing, and it is written.

Can AndroidSBC ship custom boards to Amazon FBA warehouses or 3PL consolidation points?

Answer: Yes, including DDP into Amazon FBA in the US, EU and Japan, plus 3PL consolidation points in Hong Kong, Singapore, Rotterdam, Los Angeles and Shenzhen. Cartons are labelled to FBA inbound spec and the declaration names Longgang as the origin. Partners who consolidate in Hong Kong usually take FOB Yantian and handle the last leg themselves.

How does AndroidSBC handle RMA or DOA replacements on custom boards?

Answer: AndroidSBC targets a 0.3 percent DOA rate across the WF-C3588 line, measured over the prior twelve months. On RMA, the partner returns the faulty WF-C3588-K4 unit to Longgang with its burn-in barcode, and a replacement ships within ten business days. Because the burn-in record and the configuration file are attached per unit, the failure analysis normally comes back with a root cause rather than a credit note, which matters when a custom configuration is holding up a production line.

Contact AndroidSBC: Start Your WF-C3588-K4 Sourcing Conversation

For Liverpool and United Kingdom importers, brand owners and distributors who want a direct factory relationship on the custom kiosk and pos terminal board, the AndroidSBC export desk is reachable at:

• Email: Androidsbc@163.com
• Export service hotline: +8613261677119
• Website: https://www.androidsbc.com
• Destination market file: UKCA marking with Ofcom radio interface registration for United Kingdom, administered by Ofcom, entering at Port of Felixstowe on the Felixstowe to Yantian lane
• Source factory address: Wanlin Group, Building B, Building 1, Beisida Medical Device Building, 28 Nantong Avenue, Baolong Community, Baolong Sub-district, Longgang District, Shenzhen, Guangdong, China

Custom board enquiries move fastest when the first message carries three things: annual volume, customization scope and Incoterm. With those in hand the export desk returns a per-lot quote and the WF-C3588 MOQ matrix inside two business days.